Thermal management in electric cars: design, function and common faults

When charging performance, range or the heating system become a cause for concern

Reduced charging power, unusual pump noises or weak interior heating may indicate a fault in the thermal management system. In electric vehicles, this involves more than conventional engine cooling: the battery, power electronics, electric motor, charging system and interior all require coordinated temperature control.

A single symptom does not automatically point to a specific component. Several components and control units interact with one another. Understanding the system makes it possible to narrow down the cause step by step instead of replacing parts prematurely.

VEMO and ACKOJA offer suitable repair solutions for various thermal management components, supporting targeted repairs.

What is the function of thermal management in an electric car?

Thermal management distributes and regulates heat in the vehicle. It keeps important components within a temperature range suitable for the respective operating conditions. Different thermal requirements apply when driving, charging and heating.

The battery, electric motor and power electronics generate heat during operation. At the same time, cold temperatures affect the battery’s performance. A cold battery can provide less charging and discharging power until it has reached the appropriate temperature.

That is why electric cars often have several cooling and temperature-control circuits. The circuits operate separately or are connected to one another via valves, heat exchangers, chillers and heat pumps. Their control adapts to the respective operating condition.

Which components work together?

The battery is temperature-controlled via coolant channels or cooling plates. Pumps keep the coolant moving, while valves direct the flow and switch between operating conditions. Temperature and pressure sensors provide the values used for control. A faulty sensor value can therefore change the system behaviour even if the pump or valve is still functioning mechanically.

The electric motor and power electronics must also dissipate their heat. Inverters, chargers and DC/DC converters operate with high electrical power levels. Their cooling is integrated into the respective thermal management system. Depending on the design, the electric motor is cooled with liquid or oil.

Heat exchangers transfer heat between two media or circuits. The media remain separate from one another. The chiller is the interface between the refrigerant and coolant circuits. The refrigerant circuit removes heat from the coolant. This supports, for example, battery cooling and thermal conditioning. The specific function depends on the vehicle architecture.

The interior heating is also part of the overall thermal system. Unlike an internal combustion engine, an electric drive does not provide a large amount of usable waste heat for the cabin. Electric cars therefore use electric heating systems or heat pumps. Heating problems can therefore also be caused by faulty heat distribution or control, and not only by the heater itself.

Important for diagnosis: A heat exchanger is not automatically an interior heater. “Heat exchanger” initially describes the principle of heat transfer. The specific function of a component depends on how it is integrated into the system.

Why the battery depends on temperature management

The temperature of the high-voltage battery affects how it can absorb and deliver energy. At low temperatures, the electrical resistance of the cells increases. The vehicle may therefore limit charging or discharging power until the battery has reached a sufficient temperature.

At high temperatures, heat must be removed from the battery. Otherwise, the cells may age more rapidly, or the vehicle may activate protective measures and reduce power. The applicable temperature values and the vehicle’s response are defined in the respective vehicle strategy.

A problem in the thermal management system can appear as a charging or performance issue even though the battery itself is not defective. Pumps, valves, sensors, coolant lines or the control system may also be the cause. Reduced charging power does not necessarily originate at the charging connection or charging station.

Fast charging and preconditioning

The battery temperature affects charging power. If the battery is too cold or too hot, the vehicle may limit charging power to protect the battery. A slow fast-charging process is therefore not automatically a fault at the charging point.

During preconditioning, the vehicle prepares the battery and thermal system for an upcoming charging process. If a fast-charging point has been entered as the destination, temperature control may already begin while driving. The sequence and triggers vary depending on the vehicle.

When a customer reports an issue with charging power, the workshop should therefore also consider the thermal conditions. Information about the outside temperature, state of charge and previous distance travelled, as well as available battery and coolant temperatures, is helpful. This makes it easier to assess whether the charging power is appropriate for the situation or whether further inspection is required.

Typical symptoms of a thermal management fault

A fault can become apparent during charging, driving or climate control. The circumstances under which the symptom occurs are important for the diagnosis.

Reduced or fluctuating charging power: The battery temperature and its control affect how quickly energy can be absorbed. If the charging power remains below expectations, the temperature values and thermal management should be checked in addition to the charging point and connection.

Interior heating problems: Weak or irregular heating performance may indicate a fault in the heating system, heat pump or heat distribution. The cooling of other components can also affect heating performance.

Unusual pump noises: Noticeable or unusually long pump operating times may indicate a control deviation, air in the circuit or a problem with the pump and flow rate. However, the noise alone is not sufficient for a component diagnosis.

Other possible symptoms include:

  • Problems with fast charging
  • Unusual range or changed energy consumption
  • Warning messages relating to the vehicle, battery or high-voltage system
  • Temperature values that do not match the operating condition
  • Power limited by the vehicle
  • Problems with climate control

None of these symptoms alone proves that a specific component has failed. The decisive factor is to consider fault codes, measured values and operating conditions together.

Common causes: from the component to the control system

Possible sources of faults include electric coolant pumps, temperature and pressure sensors, as well as valves. Leaks, air in the cooling circuit, restricted flow and contaminated or constricted lines and components can impair heat transfer.

Electrical and electronic faults are also possible: damaged wiring or connectors, faulty activation, communication problems between control units, as well as software or control errors. After work has been carried out on the system, air may remain in the circuit if the prescribed filling and bleeding procedure was not followed.

Diagnosing thermal management: a systematic approach

A reliable diagnosis begins with the fault codes, not with replacing the component suspected first. A stored fault code does not automatically indicate a defective component. Only comparing it with measured values, activation signals and operating conditions reveals where the actual cause lies.

  1. Compare measured values: Check temperature and pressure values for plausibility. Target and actual values provide indications of whether the sensors and control system are working consistently.
  2. Check pumps and valves: Carry out actuator tests using a suitable diagnostic device. Observe whether the expected operating condition is established and whether the flow rate is plausible.
  3. Consider electrical activation: Coolant pumps are often controlled via a PWM signal. A simple voltage measurement does not always fully display the activation signal. If the signals are unclear, an oscilloscope provides additional information about the activation.
  4. Inspect the cooling circuit: Check the coolant level and system tightness. Look for air in the system and possible flow restrictions.
  5. Follow the manufacturer’s specifications: Use only approved coolants. Follow the prescribed filling and bleeding procedures, as conventional bleeding is not sufficient for every vehicle.
  6. Check the software version: If the system reactions are implausible, it should also be checked whether relevant software updates or manufacturer specifications for thermal management control are available for the vehicle.

The manufacturer’s safety and repair specifications apply when working on high-voltage, climate-control and refrigerant systems. The appropriate diagnostic procedure depends on the specific vehicle and its system design.

When the chiller has been confirmed as the cause of the fault

If fault codes, measured values and functional tests narrow down the fault to the chiller, targeted replacement is advisable. After installation, the prescribed filling and bleeding procedures, as well as a final functional check of the thermal management system, are essential.

VEMO Chiller for TESLA MODEL 3
VEMO Chiller
VV58-97-0006, X-Ref: 1133855-00-B part 1, suitable for TESLA MODEL 3
ACKOJA Chiller for HYUNDAI KONA and KIA NIRO
ACKOJA Chiller
A53-61-0001, X-Ref: 25670-K4000, suitable for HYUNDAI KONA, KIA NIRO

FAQ about thermal management in electric cars

What are the symptoms of defective thermal management in an electric car?

Possible symptoms include reduced charging power, heating or climate-control problems, unusual pump noises, warning messages or limited power. Further tests are required for a diagnosis.

Can defective thermal management reduce charging power?

Yes. If the battery is not temperature-controlled appropriately, the vehicle may limit charging power. However, the cause does not necessarily lie with the battery itself.

What does a chiller do in an electric car?

The chiller connects the refrigerant and coolant circuits. Heat can be removed from the coolant via the refrigerant circuit, for example to control the battery temperature.

Why does an electric car need several cooling circuits?

The battery, power electronics, electric motor and interior have different thermal requirements. Separate or connected circuits help distribute and dissipate heat appropriately.

How is a thermal management fault diagnosed?

The workshop reads out the relevant fault memories, checks measured values and activation signals, and inspects the coolant level, system tightness and flow rate. The manufacturer’s specifications for the respective vehicle apply.

Don’t want to miss any new technical articles, videos and practical repair solutions?

Then sign up for our newsletter. This keeps you up to date with current workshop topics, new blog posts and technical tips for everyday workshop work.

Michael

Produktmanager

Related posts